產品介紹：
EM2210 non-contact thickness gauge measures thickness of steel pipes, flat steel, rods and other steel constructions, together with constructions made of aluminium and other metals. Measurements can be taken without usage of couplant, without advance surface preparation and across the operating gap between the transducer and the test object of up to 3 mm. Rust film, salt deposits or any other insulating coat (paint, varnish, enamel, plastic etc.) can serve as an operating gap.
EM2210非接觸式測厚儀用于測量鋼管,鋼板,棒和其他鋼鐵結構的厚度,以及鋁和其他金屬測厚。測量時不需要使用耦合劑,表面不用處理和整個操作的傳感器和測試對象之間的間隔可達3毫米, 防銹膜、鹽沉積物或任何其他絕緣涂層（油漆、清漆、搪瓷、塑料等）都可以作為操作間隙。
Test indications are slightly dependable on the skew of the transducer, unlike tradition thickness gauges with piezoelectric converters, which require fixating transducer at the specific position. Special data processing algorithm used in the EM2210 allows measuring thickness correctly even in the presence of disruptors such as metal anisotropy, several reflectors and external noise. The algorithm designed by our specialists helps to reduce influence of human factor and simplify the device interface.
在傳感器的斜度上，測試指標非?？煽?，不像傳統的厚度測量與壓電轉換器，要求固定傳感器在特定位置。在EM2210中使用的特殊數據處理算法允許在金屬各向異性、多個反射器和外部噪聲等干擾因素的情況下得到正確測量厚度。由專家設計的算法有助于降低人為因素的影響，簡化設備接口。
Connected with a tablet, smartphone or other devices based on Android OS, the EM2210 becomes an advanced flaw detector that allows users to display and save A-scan and B-scan, operate with gates, chose thickness measurement mode, signal processing parameters etc.
與平板電腦、智能手機或基于Android操作系統的其他設備，該em2210成為一個*的探傷儀，允許用戶存儲和顯示A、B型，操作門，選擇厚度測量模式，信號處理參數等。
If connected with tablet, smartphone or any other Android device, thickness meter EM2210 can operate as a modern non-destructive testing unit, suitable for A-scan and B-scan display and saving, also with opportunity to work with strobes, chose thickness measure mode, signal processing parameters etc.
如果連接平板電腦、智能手機或其它任何Android設備，em2210測厚儀可以作為一個現代無損檢測裝置，適用于A、B型顯示和保存，也有機會與閃光燈，選擇厚度測量模式，信號處理參數等。
技術參數：
Thickness range (steel) 測量范圍(鋼) | 2mm-60mm |
Measurement uncertainty測量精度 | 0.08mm |
Operating gap between the transducer and the test object傳感器與測試對象之間的工作間隙 | 0 to 3mm |
Operating transducer skew relative to normal to the test object surface操作換能器傾斜相對于正常的測試物體表面 | ±25 degrees ±25度 |
Acoustic speed adjustment range聲波速度調節范圍 | 16 |
Acoustic speed range adjustment聲波速度范圍調整 | 1000…9999 m/s in 1 m/s increments |
Operating frequency range工作頻率范圍 | 3.5 MHz |
Continuous work time on a single charge一次充電的連續工作時間 | 5 hours 5小時 |
Wave type波形 | Shear wave radially polarized in a plane of a surface of the monitored object在被監測物體表面的平面上的橫波徑向偏振 |
Operating temperature range使用溫度范圍 | -20…+50 |
Dimensions尺寸 | 163 x 39 x 32 mm |
產品圖片：
